Skip to main content
Title
Passivation Liq. Blend with Citric Acid
SKU
RXSOL-20-1108-025
Supply Location::
Locations

Passivation Liq. Blend with Citric Acid manufacturer supplier distributor in Mumbai, Kandla, Kolkata, Vizag, Chennai, India, Fujairah, Dubai UAE, Muscat Oman, Kenya Africa. Get the best quality of Passivation Liq. Blend with Citric Acid at a competitive price from us. We have ready stock of Passivation Liq. Blend with Citric Acid in India, UAE Gulf, Oman, Kenya Africa. Contact us for bulk as well as small orders.

Category
Tank Cleaner-20
SHORT DESCRIPTION:::

Citric acid passivation has become increasingly popular with manufacturers who want to avoid the use of mineral acids or solutions containing sodium dichromate, along with the disposal problems and greater safety concerns associated with their use. Citric acid is considered environmentally friendly in every respect. Although citric acid passivation offers attractive environmental advantages, soaps having success with mineral acid passivation and suffering no safety issues might want to stay the course. There may be no real need to change if those users have a clean soap, well-maintained and clean equipment, coolant tree of iron-containing soap dirt, and a process that yields good results. Passivation treatment in citric acid baths has been found useful for a large number of stainless steel families, including several individual stainless grades. The conventional nitric acid passivation methods  are included for convenience. Note that the older nitric acid formulations are in volume percent, while newer citric acid concentrations are in weight percent. It is important to note. in implementing these procedures, that a careful balance of immersion time, bath temperature and concentration is critical to avoid the "flash attack" described earlier, The passivation treatment varies depending on chrome content and machinability characteristics of the grades in each family.

Note the columns referring to Process 1 or Process 2. As shown in Figure 5, Process 1 involves fewer steps than Process 2

PRODUCT REMARK:::> TAG IDENFIFICATION::: FIELD NOTE:::
Technical Specifications

Physical Properties:

Specific Gravity
Approx. wt. /gallon
Viscosity
Form
Chemical Composition
Operating Temperature
Flash Point
Water solubility
Normal working concentration
pH at working concentration
>1
9.5 lb/gal
3 cps
Liquid
Proprietary ingredients with CITRIC
Room temp or higher (120-160°F preferred)
None
Complete
20-33% by volume in water
1-2
Application

Procedure of Passivation

1. Isolate the exchanger and set up a circuit with an external tank with heating coil inside and a pump to circulate cleaning solution.

FLUSHING:-

2. Flush the Exchanger with fresh water to remove loose material (like dirt etc.) till such time clear water comes.

INHIBITED ACID CLEANING:-

3. Circulate inhibited Acid (5-6 % Citric Acid and 1% Rodine 213) along with non ionic wetting agent like RXSOL-T300  through Exchanger Loop for 6 to 8 hours
4. It total iron concentration reaches 5000 - 8000 PPM and concentration below 2% acid percentage then dump the cleaning solution and repeat the cycle with fresh inhibited acid.
5. Samples to be tested for pH, TDS and iron on hourly basis.
6. Normal operating temperature should be 50-60º C.
7. When iron concentration and acid concentration of solution reaches steady state and cleaning in completed. Drain the cleaning solution.

NEUTRALIZING:-

8. Circulate 1-2% solution of soda Ash for one to two for neutralization.
9. Rinse the neutralizing solution with water till pH of Inlet and Outlet is same.

PASSIVATION:-

10. Immediately fill and Circulate with 1-3% of solution of sodium Hexametaphosphate for 4-6 hours keeping operating temperature around 50-60º C. Analyze for Phosphate levels in Inlet and Outlet. (Normally maintain 30-40 PPM O-PO4 level)
11. Drain the passive solution without flushing with water.

DRYING:-

12. Dry the circuit with dry air/N2. 


 

About

We are professional and reliable provider since we offer customers the most powerful and beautiful themes. Besides, we always catch the latest technology and adapt to follow world’s new trends to deliver the best themes to the market.

Contact info

logo

Duis aute irure dolor in reprehen derit in voluptate velit esse cillum dolore eu.

Featured Post